Car Connector (ADC-3035L) – Installation Guide

How Can We Help?

You are here:
< All Topics

Extend security and awareness outside a home or business with Alarm.com’s Connected Car. Track a vehicle’s location, view engine status, and analyze fuel efficiency – right from the Alarm.com mobile app.

Customers can enjoy peace of mind with real-time driver safety alerts, diagnostic alerts, and more. Use this guide to quickly and easily install the Car Connector, a device that plugs into a vehicle’s OBD-II port, connecting the vehicle to the Alarm.com platform.

Installation precautions 

  • Choose a safe location before installing, removing, or reconnecting the Car Connector.
  • The Car Connector should never be plugged into or unplugged from the vehicle’s OBD-II port while the vehicle’s ignition is ON or in ACC/ACCESSORY mode, as this may cause issues such as dashboard lights to come on, but that should not affect the operation of the vehicle itself. Please ensure that the ignition is completely OFF before plugging in or unplugging the Car Connector. Should dashboard lights come on, they can usually be cleared by turning off the ignition and unplugging the Car Connector.
  • When the Car Connector is plugged in, ensure it is installed securely and cannot easily be removed or come loose. If necessary, make use of cable ties to ensure a secure connection.
  • Do not install the Car Connector in a manner that could obstruct the driver’s ability to safely operate the vehicle. If necessary, make use of an OBD-II extender cable to re-locate the position of the Car Connector.
  • The Car Connector cannot share the Vehicle Bus (its internal communication network) with other devices that are also connected to the Vehicle Bus. Do not use the Car Connector in vehicles with devices such as wheelchair lifts or OnStar® that also communicate on the Vehicle Bus, or with a Y-cable to connect multiple devices to the OBD-II port at the same time.
  • The Car Connector uses a small amount of power from the vehicle battery while the ignition is off. If the vehicle’s ignition will be off for more than a week, it is recommended to unplug the Car Connector to prevent the possibility of draining the vehicle battery.

Pre-installation checklist

  • Car Connector (included)
  • Vehicle with an OBD-II port (standard on vehicles manufactured in 1996 or later). Hybrid and electric vehicles are not currently supported.
  • The vehicle should not be in an underground garage or in an area where cellular coverage may not be available.
  • A smartphone or tablet with an Internet connection.
  • Connected Car must be selected on the customer’s service package. Up to five cars can be set up with Connected Car on a single account.

Add the Car Connector to an account

Before the Car Connector can send a vehicle’s information to Alarm.com, it must be added to an account.

It is recommended to add the Car Connector using the Add Device Portal in the Customer app. If you do not have access to the customer’s login credentials, see Log in as customer or mobile user for more information about how to log in as a customer using the MobileTech app before following the steps below.

To add the Car Connector to an account using the Partner Portal:
  1. Log into the Partner Portal.
  2. Find the customer account.
  3. Click Equipment.
  4. Click Car Connectors.
  5. Click Add Car Connector.
  6. Tap Car Connector.
  7. Follow the on-screen instructions to install the Car Connector and add it to the account.
  8. The new Car Connector should now appear in the Car Connectors table.

    Note: If the vehicle’s OBD-II port reports the VIN, the Device Name column will update with the name of the vehicle once the Car Connector is plugged into the vehicle. Many older vehicles do not report the VIN, so if this column does not update, it is not a cause for concern.

To add the Car Connector to an account using the MobileTech app:
  1. Log into the MobileTech app.
  2. Find the customer account.
  3. Tap Equipment.
  4. Tap Car Connectors.
  5. Tap to expand Car Connector Actions.
  6. Tap Add Car Connector.
  7. Tap Start Add Device Wizard.
  8. Tap Log In As User To The Web Site. The Car Connector can be added with View Only access.
  9. Tap Car Connector.
  10. Follow the on-screen instructions to install the Car Connector and add it to the account.
  11. The new Car Connector should now appear in the Car Connectors table.

    Note: If the vehicle’s OBD-II port reports the VIN, the Car Monitor row will update with the name of the vehicle once the Car Connector is plugged into the vehicle. Many older vehicles do not report the VIN, so if this row does not update, it is not a cause for concern.

To add the Car Connector to an account using the Add Device Portal:

Note: The Car Connector will not appear as an option until its installation wizard is enabled. For information about enabling the Car Connector installation wizard, see Add Device Portal.

  1. Log into the Customer app. The customer’s username and password are required to log into the account.
  2. Tap .
  3. Tap + Add Device.
  4. Tap Car Connector.
  5. Follow the on-screen instructions to install the Car Connector and add it to the account.

To add the Car Connector by scanning the QR code:
  1. Scan the QR code below. The customer’s username and password are required to log into the account.


     
  2. Follow the on-screen instructions to install the Car Connector and add it to the account.
To add the Car Connector to an account using the Customer Website:
  1. Using a web browser, visit www.alarm.com/addcarconnector. The customer’s username and password are required to log into the account.
  2. Follow the on-screen instructions to install the Car Connector and add it to the account.

LED guide

Ignition state
LED patternDescription
Red OffIgnition is off or vehicle has not been detected
Ignition is on

Communication
LED patternDescription
Orange OffModem is off
Connected to Alarm.com
Searching for cellular network
Connected to the cellular network but not to Alarm.com

GPS
LED patternDescription
Green OffGPS is off
GPS is on and the current location has been determined
GPS is on, searching for a location
Requesting time from the GPS satellites



Troubleshooting

Car Connector is showing as not responding in the Customer app

Alarm.com has not heard from the Car Connector in more than 24 hours. Ensure the Car Connector is firmly plugged into the vehicle’s OBD-II port and that it is in an area with cellular coverage.

“Unplugged” or “plugged in” events or notifications are received when the Car Connector was never unplugged

The Car Connector may have a loose connection to the OBD-II port. Ensure that it is firmly plugged in and use an extension cable if necessary.

The Customer app status shows “engine on” when the vehicle is off

The Car Connector may have lost cellular connectivity and cannot send an engine off message. This is common when the vehicle is parked in an area where cellular coverage may not be available, such as an underground garage. The message will be sent when connectivity is restored.

The car never appeared on the Cars card in the Customer app
If the orange LED is not solid: 
  1. Park and turn off the car. 
  2. Unplug the Car Connector and plug it back in or move the vehicle to an area with better cellular coverage.
  3. Try the installation again following the Installation precautions and subsequent directions.
If the orange LED is solid and the red LED is off: 
  1. Park and turn off the car. 
  2. Unplug the Car Connector and plug it back in.
  3. Try the installation again following the Installation precautions and subsequent directions.

    Note: If the vehicle is a pre-2008 model year, verify the Car Connector has been plugged into the OBD-II port with the ignition on for 30 minutes before attempting a fix.
Each trip is displayed as multiple smaller trips in the Customer app

Your vehicle may have stop-start technology, which means the engine shuts off to save fuel when the vehicle is idling. Go to the Car Settings page in the Customer app and turn on the Stop-Start Technology setting. If the vehicle is idling for long periods of time, it may still cause trips to be broken up.



Frequently asked questions

Can a standalone Connected Car account be created?

Yes. When creating a customer account, select Standalone (Access Control, Video, Cellular Sensor and/or Connected Car) to create an account that only includes the Connected Car solution. For more information about creating customer accounts, see How to create Alert 360 customer account.

How many Car Connectors can be added to a customer account?

Up to five Car Connectors can be used simultaneously on a single customer account.

Does the Car Connector need to be deleted and re-added when installed in a new vehicle?

No. The new car should detect the Car Connector once it is plugged in and the ignition is started. Once calibration is complete after the first trip or so, the device name should update automatically to the make and model of the new car.

What if the device obstructs normal driving operation when plugged in?

The Car Connector can be connected to an OBD-II extension cable for installation in a better location in the vehicle. Never use the device in a way that could potentially interfere with your ability to safely operate the vehicle.

Why is the fuel level not displaying for the vehicle?

Reading of the fuel level is not supported on the vehicle. The fuel level can only be displayed when the vehicle reports a value through the OBD-II port and the Car Connector is able to read it.

What is the Hibernating status?

If your car’s engine has been off for a week, the Car Connector will enter a deep sleep mode to prevent draining the car’s battery. The Car Connector will stop communicating information until the engine is started again.

Why didn’t the customer get a notification when the low fuel indicator on the vehicle dashboard turned on?

The low fuel notification is sent when the fuel level drops below the user-defined threshold in the Car Settings page in the Customer app that may be different from when the vehicle reports low fuel.

When will the customer get notifications for excessive speed, sudden acceleration, or hard braking?

Thresholds for these alerts can be configured by going to the Car Settings page in the Customer app.



Notices

Federal Communication Commission interference statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

IC Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:

(1) L’appareil ne doit pas produire de brouillage, et

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

RADIATION EXPOSURE STATEMENT

The device has been found to be compliant to the requirements set forth in CFR 47 Sections 2.1091 and Industry Canada RSS-102 for an uncontrolled environment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Le dispositif a été jugé conforme aux exigences énoncées dans les articles 47 CFR 2.1091 et Industrie Canada RSS-102 pour un environnement non contrôle’. L’antenne(s) utilisée pour ce transmetteur doit etre installé pour fournir une distance de séparation d’au moins 20 cm de toutes les personnes et ne doit pas être co-localisés ou fonctionner en conjunction avec une autre antenne ou transmetteur.

Was this article helpful?
0 out Of 5 Stars
5 Stars 0%
4 Stars 0%
3 Stars 0%
2 Stars 0%
1 Stars 0%
5
How can we improve this article?
Please submit the reason for your vote so that we can improve the article.
Table of Contents

Still having trouble?

Contact Customer Care